OE Ref.:
42607-30060
Commercial Name:
Pacific Clamp-in Gen 2 314.9 MHz Toyota FSK ver 2
OEM Sensor P/N:
42607-30060; 42607-0D010
Ean Code:
EZ-sensor® coverage:
NO
Nut Torque:
35.4 in-lbs (4 Nm) Nm
Screw Torque:
-- Nm
Valve Core Torque:
3.5 in-lbs (0.4 Nm) Nm
Note:
Aftermarket OE replacement sensor not yet availalbe for sale
WARNING: This product contains chemicals including lead, which is known to the State of California to cause cancer and reproductive issues.
For more information, go to
www.P65Warnings.ca.gov.
EZ-sensor® GO is pre-programmed for all vehicles mentioned in the list. No programming is required before installation for the below applications. Additionally, the sensor can be programmed to 99% of all vehicle makes, models and years.
Click on item for more details:
This list is being continuously updated.
Part No.:
1109
20032
20032
Commercial Name:
TPMS Service Pack
Note:
Contents: 1 Aluminum Nut, 1 Plastic Sealing Cap, 1 Rubber Grommet, 1 Nickel Plated Valve Core, 1 Aluminum Washer
EZ-sensor® GO can be programmed to any Make Model and Year shown in this list.
Click on item for more details:
This list is being continuously updated.
Relearn Summary: OBD Relearn
Relearn DescriptionNOTE: Not all Models came equipped with a TPMS reset button.
If no button is found, then a relearn is not required following an air pressure adjustment, tire rotation, or tire replacement.
This button is commonly located on the driver’s side knee bolster, inside the glove compartment, under the steering wheel, or next to the DLC/OBDII.
The purpose of this button is to set a base-line for the air pressure and re-establish communication between the sensors and the vehicle.
Initialization following rotation and tire replacement:
1. Inflate all tires to pressure listed on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Hold down tire pressure reset button (located on instrument panel, knee bolster, or inside glove box) until TPMS telltale flashed 3 times.
4. Initialization will be completed when ECU has received signals from all sensors. Process may take 2-3 minutes.
5. If initialization is not complete, drive vehicle for approximately 20 minutes.
Initialization following new sensor installation:
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors. After IDs have been registered via the OBD, leave ignition on, and activate all sensors using TPMS activation tool.
TIA troubleshooting tip: Many Toyota SUV’s and Minivans have a Main / 2nd Switch commonly located inside or under the glove box, or at the base of the knee bolster.
(See image below) This switch allows the vehicle to store two sets of TPMS ID’s. One set for Spring / Summer wheels / tires and a second set for Fall / Winter.
When the button is not pressed, the system is monitoring the OEM or “main” IDs on the vehicle.
When pressed, the vehicle can then monitor a second set of IDs that can be stored for winter wheels/tires.
If the button is pressed and no IDs are entered under the second position, then the MIL will illuminate.
So ensure the you are writing the sensor IDs to the correct postion.
Relearn Procedure as PDF document
Mounting Instructions
Note:
Sensor images shown in this document are for illustration purpose only!
Phisical sensor body may be different.
Non contractual document!
For tecnical information, please contact your supplier or leave a message at info@Schrader TPMS E-Catalog.com
User Manual/Quick Start Guide
Note:
Document contains full description user manual and / or Quick Start Guide. Non contractual document!
For technical information, please contact your supplier or leave a message at SchraderNA@sensata.com
Approvals and Declarations
Note:
Package contains FCC, IC and CE certifications
Physical sensor body may be different.
Other documents can be also found
here.